Reduce rootfs size a bit by installing the separated firmware packages
instead of the large linux-firmware-qcom package. Also, install the
modem firmware by default to prepare for enabling GPS.
Squash the packaged venus firmware blobs using pil-squasher so only
one file needs to be loaded rather than many small ones. Linux detects
squashed (.mbn) vs non-squashed (.mdt + .b*) based on file contents
(not file name) so it is fine to install venus.mbn to venus.mdt.
Strictly speaking firmware-bq-picmt is not needed anymore because
the msm-firmware-loader can be used to load the picmt firmware from
the firmware partitions. However, this package contains quite recent,
largely unmodified firmware from Qualcomm so it still seems useful
to keep if someone wants to test more recent firmware on some other
device (provided that their device does not verify firmware signatures).
To make this firmware package consistent with firmware-qcom-db410c,
squash the firmware blobs using pil-squasher so only one file needs
to be loaded rather than many small ones.
firmware-qcom-msm8916-wcnss is a virtual package used for MSM8916
devices without secure boot (i.e. device that do not require signed
firmware). For those it's best to install more recent firmware by
default rather than using the firmware on the firmware partition.
firmware-qcom-msm8916-wcnss is provided by firmware-qcom-db410c-wcnss
by default, however it's still useful to make it possible to switch to
the stock firmware on the firmware partition if needed. To allow that,
add a dummy msm-firmware-loader-wcnss package that provides the virtual
package using the msm-firmware-loader.
# apk add msm-firmware-loader-wcnss
(1/2) Purging firmware-qcom-db410c-wcnss (1034.2.1-r2)
(2/2) Installing msm-firmware-loader-wcnss (1-r1)
Unfortunately, at the moment MSM8916 devices always have to install
all of linux-firmware-qcom (~ 60 MiB) when they actually just use
~ 0.008 MiB of GPU firmware in there. Everything else is just big
firmware blobs for other SoCs that are never going to be useful.
It's much more efficient to package the necessary firmware separately
to save rootfs space. The DB410c linux-board-support-package contains
all the firmware from linux-firmware as well, so we can easily package
it as part of the firmware-qcom-db410c package.
This commit makes the following changes to firmware-qcom-db410c:
1. Package venus() firmware that was previously installed from
linux-firmware-qcom. GPU firmware is packaged in firmware-qcom-adreno.
2. Use new firmware paths for DB410c that were applied upstream
3. "Squash" the firmware blobs to a single file using pil-squasher
Make the package consistent with firmware-qcom-adreno packaged from
linux-firmware, but keep them separate for legal reasons. The firmware
packaged in firmware-qcom-adreno-extra does not have a proper license.
[ci:ignore-count]
[ci:skip-build] already built successfully in CI
Add a new firmware-qcom-adreno APKBUILD that packages the GPU firmware
from upstream linux-firmware as separate packages. It is basically
a minimal replacement for linux-firmware-qcom that allows saving rootfs
space by installing only the firmware that is really relevant for the
device.
[ci:skip-build] already built successfully in CI
* xts, libaes & aes are required for root partition FDE unlocking
* evdev is required by osk-sdl for input
[ci:skip-build] already built successfully in CI
This seems to fix the last missing piece to getting the hotspot stuff
working, at least when it's set up with networkmanager (I haven't tested
other methods, but assume this rule is still needed there too...)
fixes#1198
The firmware provided by these subpackages is now covered by the
msm-firmware-loader, so there is no need to build packages for them
anymore.
[ci:ignore-count]
The "replaces"/"provides" should have the full package name, not just
the part of the subpackage. Also, the nonfree-firmware subpackage does
not need it because the old "device-xiaomi-wt88047-nonfree-firmware-modem-wt88047"
packages were only install_if packages without any files installed.
The files packaged in firmware-motorola-osprey-wcnss-nv and
firmware-motorola-osprey-venus seem completely identical to those
of harpia, so there is no need to package them twice. There are some
differences in modem/wcnss firmware but those are now covered by the
msm-firmware-loader.
Add sony-fusion3 firmware subpackage to enable wifi.
Enable Qoalcomm Prima WLAN driver and fix wrong path in kernel.
[ci:skip-build] Already built on CI in MR
Touchscreen and usb networking works. Much of the hardware is the
same as on gts210velte (but that one has a qcom soc and not
exynos5433). Exactly the same touchscreen calibrarion as for
gts210velte works for this device as well.
Also include firmware package with wifi files. Unlike on many other
Samsung devices wifi does not work out of the box after these
firmware files has been added.
[ci:skip-build] Already built on CI in MR
I'm not sure it is possible to connect a second display to this phone
through P2P WiFi, so mapping cursor to DSI-1 just in case. It is needed
for screen rotation when a second display is connected.
Reduce scaling factor from default 2 to 1.8.
I'm not sure it is possible to connect a second display to this phone
through P2P WiFi, so mapping cursor to DSI-1 just in case. It is needed
for screen rotation when a second display is connected.
Reduce scaling factor from default 2 to 1.8.
Installing postmarketos-base currently changes the file permissions
of /etc/sudoers:
# apk add sudo
# stat /etc/sudoers
Access: (0440/-r--r-----) Uid: ( 0/ root) Gid: ( 0/ root)
# apk add postmarketos-base
# stat /etc/sudoers
Access: (0044/----r--r--) Uid: ( 0/ root) Gid: ( 0/ root)
The file mode 0044 decodes to:
- User *cannot* read
- Group can read
- Other can read
which does not make any sense. The "sudoers" man page makes it very
clear that this file should have a file mode of 0440 [1]
("readable by owner and group, writable by none").
This looks like a bad typo. However, given that only read permissions
were given out this shouldn't have major security implications
(except allowing all users to see who can use sudo).
Install the file with 0440 instead of 0044 to fix this:
# apk add postmarketos-base
# stat /etc/sudoers
Access: (0440/-r--r-----) Uid: ( 0/ root) Gid: ( 0/ root)
[1]: https://www.sudo.ws/man/1.9.8/sudoers.man.html#Error_log_entries
Minecrell