This device port is unmaintained: The mainline port (xiaomi-wt88047)
is preferred. This is only intended for testing, and was used to validate
the battery/charging driver as one example. Various patches are used
for the downstream kernel that expose helpful information for debugging.
[ci:skip-build]: already built successfully in CI
These are various debugging related patches that I have used over the time
when attempting to get new features working for the mainline kernel.
Given that the downstream kernel is just intended for debugging in this case,
it seems convenient to add them to pmaports so I don't need to go search for
them in case I need them again in the future.
[ci:skip-build] Already built on CI
Resize the partition when using a pre-built image. We didn't notice that
this was missing, because N900 images are new and we only tested from
pmbootstrap install --sdcard, which already uses the full SD card size.
modules-load.conf was completely unused by this package,
not installed anywhere. brcmfmac is loaded automatically anyway.
Sort values in sources= alphabetically
This is needed with the 5.11 kernel. Also adjust the vram & cma sizes
for all msm8974 devices.
The CMA size is 256MB as set in the kernel config.
VRAM is default 16MB although it is set to 192MB with a kernel patch;
but set it manually for all devices to make it possible to remove this
patch in the future - until we have IOMMU working.
still missing:
* audio
* lcd backlight control
* touchscreen driver
* front camera
* accelerometer mount fix (driver seem not to support mount-matrix)
* 3D acceleration
* HDMI support
This allows loading nonfree fw from rootfs (/lib/firmware), to work
around: https://source.puri.sm/Librem5/linux-next/-/issues/290
This change will break wifi unless the nonfree
firmware-siliconlabs-rs9116 package is installed.
New mainline port with most things working (usb/wifi/bt/3d-accel/sound/gps).
Modem/calls/sms/mobile-data should work but couldn't test it recently
due to broken devices.
* Add u-boot build with a lot of patches that makes the display work in
u-boot for boot selection
* Upgrade the rockchip kernel to 5.11 mainline with config for the
rk3399 devices built-in
* Make the rockpro64 and pinebook pro use the newer kernel
[ci:skip-build]
Actually the display in asus-me176c has a width of 800px, which means
that the splash screen isn't perfectly centered. Correct this in
deviceinfo to make it show up correctly.
Also, add configuration file for Phosh to reduce scaling a bit to 1.75.
It's kind of subjective but scaling = 2 definitely feels too large.
[ci:skip-build]: already built successfully in CI
There's a race condition between when the pwmled device is initialized,
which kicks off a feedbackd udev rule that configures the led trigger to
'pattern', and when ledtrig_pattern actually loads. It seems to mostly
load after the rule runs, so the trigger is never set to 'pattern' on
boot.
This removes the race by building the ledtrig_pattern driver into the
kernel.
[ci:skip-build] Already build successfully in CI
This patch fixes a fairly severe performance regression with wifi on the
L5 (something like 20x improvement in performance with this patch)
[ci:skip-build] Already build successfully in CI
The device has been renamed from fujitsu-m532 to pegatron-chagall since several rebrands of this board exist (Olivetti Olipad3, Siragon 4N, etc.), and Fujitsu M532 is just one of those.
Signed-off-by: Raffaele Tranquillini <raffaele.tranquillini@gmail.com>
Ship mode via the mechanism used by purism doesn't work; it's either not
possible or outside my understanding to run an openrc runscript with a
busybox init on *poweroff* and *not reboot*, which is what is required
for this to work properly..
This module param requires a corresponding kernel patch to enable ship
mode support in the bq25890-charger module
Minecrell