This new package covers all three variants of the tablet: the WiFi
version (SM-T310), the 3G version (SM-T311) and the LTE version
(SM-T315). It uses the linux-postmarketos-exynos4 kernel, like other
mainlined Exynos 4 devices.
- The 3 different variants of the lt01 will be merged into a single
main device package, so the old package is deprecated.
- We will now be using the mainline kernel, so the downstream kernel is
no longer necessary.
- Add a patch to fix a new build error.
Now as boot-deploy allows us to generate both boot.img and extlinux.conf
at the same time, enable generating the config for all msm8226 since it
will be used in the future lk2nd release. boot.img is still kept to keep
compatibility with current lk2nd releases and to allow system recovery
with fastboot when required.
[ci:skip-build]: already built successfully in CI
pmOS does not support charge mode anyway, and boots to a full UI, but this vendor kernel disables touchscreen when booting in charge mode. Remove that check, so that the phone can be used as usual.
[ci:skip-build]: already built successfully in CI
- kconfig changes from `pmb kconfig migrate`
- also enabled some USB serial drivers I wanted
- Reverts 7dcd3e014aa7, fixing bluetooth connections. This commit was
added after 6.8-rc6 and causes a regression. A revert was sent
upstream: https://lore.kernel.org/all/ZfMStHjwtCT1SW3z@hovoldconsulting.com/
[ci:skip-build] already built successfully in CI
A number of fixes:
- oem-amd-nonfree-fw no longer exists from c6306cb9b, and the fw here is
pretty much required for the device to be useful so it's added to
"depends=".
- drops the -vulkan subpackage since oem-amd-vulkan is doing the same
thing.
- force rootfs partition resize on boot, else the rootfs is too small
- disable unudhcpd, usb networking isn't working, and we don't need to
run it on any dedicated eth device
- use kernel with Valve's out of tree patches, to improve stability /
usefulness of device
fixes#2630
[ci:skip-build] already built successfully in CI
There are some important platform drivers that Valve has not upstreamed,
that are basically required for this device to operate well. I picked
those patches from the kernel tree they released for 6.5, and rebased
them onto 6.8.
Our config.txt is replaced (mv'ed to config.txt.old, maybe by alpine's
initramfs-generator?) and so our configuration does not have an
effect. Put our config stuff in usercfg.txt instead, which is included
by config.txt.
Fixes: https://gitlab.com/postmarketOS/pmaports/-/issues/2471
[ci:skip-build]: already built successfully in CI
Our config.txt is replaced (mv'ed to config.txt.old, maybe by alpine's
initramfs-generator?) and so our configuration does not have an
effect. Put our config stuff in usercfg.txt instead, which is included
by config.txt.
Also update vmlinuz name, should be vmlinuz-rpi and not vmlinuz-rpi4.
Name of package in aports is linux-rpi these days. linux-rpi provides
linux-rpi4 for backward compatibility, so depending on linux-rpi4
still works, but lets use real package name so that it is easier to
find.
These are now provided by linux-firmware-brcm, which subsequently causes
a conflict between these packages. Fix it by removing the symlinks from
the device package.
Closes https://gitlab.com/postmarketOS/pmaports/-/issues/2616
[ci:skip-build]: already built successfully in CI
Changes:
- use msm-firmware-loader
- use soc-qcom-msm8953
- cleanup firmware package
- add tqftpserv as a dependency for modem
- add modules-initfs with panel and touchscreen modules
[ci:skip-build]: already built successfully in CI
Unfortunately we cannot get to a getty shell unless we also run:
setenv SWITCH_SEL 3
from the SBL shell. Furthermore, actually getting kernel output
requires setting console=ttySAC2,115200.
SWITCH_SEL might be related to the "MUIC" of the device, but the
variable also controls whether or not it is possible to get serial
output from pads on main board, and seems weird that those pads are
affected by MUIC (unless pads are also behind MUIC, but seems like
that would be very annoying when developing the device)
See also initial MR where mainline support for i9100 was added, where
serial output is also discussed:
https://gitlab.com/postmarketOS/pmaports/-/merge_requests/1598#how-to-get-serial-output
[ci:skip-build]: already built successfully in CI
Added postmarketos-base-downstream and msm-fb-refresher to jxelte
dependencies.
The modules_install and firmware_install targets install binary
files as the zram files among others.
Added the 'mfc_fw.bin' binary to be installed from the firmware
package.
The '0002-fix-usb-gadget-random-mac.patch' patch make it possible
to get ethernet over usb, and the 'disable-charging-bootmode.patch'
avoid error messages on dmesg about 'sec_battery_probe'.
[ci:skip-build]: already built successfully in CI
Fix incomplete commit ecc91098a9 that
was missing the dependency on
"postmarketos-base-downstream-disable-udev-v4l".
Fix MR !4768
[ci:skip-build]: already built successfully in CI
This fixes building for linux-lg-vee7e, and adds a shared patch.
The shared patch replaces the "Solaris style flags" in piggy.gzip.S
[ci:skip-build]: already built successfully in CI
fossdd