Add the missing depends to add the GPU firmware to the initramfs
so that osk-sdl works properly, as well as the haptics driver.
Also make all logs go to UART, this will clean up the splash screen and
let developers with UART access debug the boot process.
[ci:skip-build] This MR was already built on CI
Add the missing depends for our soc package alsa ucm configs. Also add
the missing depends to add the GPU firmware to the initramfs so that
osk-sdl works properly!
Also enable logs and point them to UART, this will clean up the splash
screen and let any developers with UART attached to debug the boot
process.
AsteroidOS uses this config file to determine how the UI should look
(e.g. a round or a square screen), and if some things like Wi-Fi are
supported. Upstream auto generates this config file, but it seems so
simple and small that I think it's better for us to just ship the file
next to the APKBUILD
AsteroidOS uses this config file to determine how the UI should look
(e.g. a round or a square screen), and if some things like Wi-Fi are
supported. Upstream auto generates this config file, but it seems so
simple and small that I think it's better for us to just ship the file
next to the APKBUILD
The PMIC AXP803 sends an interrupt to the A64 CPU when the
battery is critical low. This wakes up the tablet at ~10%
battery level, but UPower wasn't configured to add upon
this interrupt as the action level was way lower.
Therefore, the PMIC performed a hard shutdown when the
battery level dropped further, which may cause data loss.
The PMIC AXP803 sends an interrupt to the A64 CPU when the
battery is critical low. This wakes up the phone at ~10%
battery level, but UPower wasn't configured to add upon
this interrupt as the action level was way lower.
Therefore, the PMIC performed a hard shutdown when the
battery level dropped further, which may cause data loss.
TF201 nvram was updated since previous did not work on some devices.
Added support for TF101, TF300TG and TF300TL.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Gummiboot was dropped from Alpine. Switch to grub, which is what we use
for tablet-x86uefi too.
In contrary to tablet-x86uefi, run the grub-mkimage command directly
inside the device package:
* This avoids creating another confusing grub-x86 like package (looks
like the x86 version of alpine's grub package, as it's the case with
grub-efi-x86, but actually it is just the result of grub-mkimage).
* In contrary to grub-efi-x86, the resulting efi file is not shared
across several devices.
* It's consistent with uboot mkimage commands, which we also run in
device packages.
Related: https://gitlab.alpinelinux.org/alpine/aports/-/commit/398b7aef0b86c477103ba592526ebb9940a44509
We used to have it at 40% and just bumped it to 100%. With 100%, I can
hear static noise in the headphones when using the PinePhone (pmOS CE)
in a silent room, even if I turn the volume down in Pulseaudio (e.g.
18%-30% in Phosh). This was not the case when we had it at 40%.
70% seems to be the sweet spot, where no static noise can be heard when
using headphones in a silent room, but where volume can still be turned
up to a very high level if necessary.
Ported succesfully to armv7. Everything that worked on armhf
works on armv7 as well: touch, wifi, usb networking etc.
SWRast (gallium) was not enabled but is needed because the device
does not support 3D acceleration yet.
Upstream changelog:
https://source.puri.sm/Librem5/linux-next/-/commit/ca736e844a6b63967d135c2280e5696f0a95934e
Patches rebased, and includes some new fixes:
arm64-dts-imx8mq-librem5.dtsi-adjust-the-usdhc-bus-s.patch
- Being tested by Purism as well, has shown some promise improving GPS
reliability
arm64-dts-imx8mq-disable-SuperSpeed-instances-in-par.patch
- Fixes issue with modem disappearing
This is required for kernels earlier than 4.7 for bwrap to work for
normal users, and therefore for gnome web (epiphany) and flatpak.
[ci:skip-build] [ci:ignore-count]
Newbyte