167 lines
4.5 KiB
ReStructuredText
167 lines
4.5 KiB
ReStructuredText
.. SPDX-License-Identifier: GPL-2.0+
|
|
.. sectionauthor:: Dominik Haller <d.haller@phytec.de>
|
|
|
|
phyCORE-AM68x/TDA4x
|
|
===================
|
|
|
|
The `phyCORE-AM68x/TDA4x <https://www.phytec.eu/en/produkte/system-on-modules/phycore-am68x-tda4x/>`_
|
|
is a SoM (System on Module) populated with AM68x or TDA4x SoCs from TI's J721S2
|
|
family. It can be used in combination with different carrier boards. This module
|
|
can come with different sizes and models for DDR, eMMC, ETH-PHY, SPI NOR Flash
|
|
and an optional SN65DSI83 DSI->LVDS transceiver using DSI0.
|
|
|
|
A development Kit, called `phyBOARD-Izar <https://www.phytec.eu/en/produkte/development-kits/phyboard-izar/>`_
|
|
is used as a carrier board reference design around the AM68x/TDA4x SoM.
|
|
|
|
Quickstart
|
|
----------
|
|
|
|
* Download sources and TI firmware blobs
|
|
* Build Trusted Firmware-A
|
|
* Build OP-TEE
|
|
* Build U-Boot for the R5
|
|
* Build U-Boot for the A72
|
|
* Create bootable uSD Card
|
|
* Boot
|
|
|
|
Sources
|
|
-------
|
|
|
|
.. include:: ../ti/k3.rst
|
|
:start-after: .. k3_rst_include_start_boot_sources
|
|
:end-before: .. k3_rst_include_end_boot_sources
|
|
|
|
.. include:: ../ti/k3.rst
|
|
:start-after: .. k3_rst_include_start_boot_firmwares
|
|
:end-before: .. k3_rst_include_end_tifsstub
|
|
|
|
Build procedure
|
|
---------------
|
|
|
|
Setup the environment variables:
|
|
|
|
.. include:: ../ti/k3.rst
|
|
:start-after: .. k3_rst_include_start_common_env_vars_desc
|
|
:end-before: .. k3_rst_include_end_common_env_vars_desc
|
|
|
|
.. include:: ../ti/k3.rst
|
|
:start-after: .. k3_rst_include_start_board_env_vars_desc
|
|
:end-before: .. k3_rst_include_end_board_env_vars_desc
|
|
|
|
Set the variables corresponding to this platform:
|
|
|
|
.. include:: ../ti/k3.rst
|
|
:start-after: .. k3_rst_include_start_common_env_vars_defn
|
|
:end-before: .. k3_rst_include_end_common_env_vars_defn
|
|
.. code-block:: bash
|
|
|
|
$ export UBOOT_CFG_CORTEXR=phycore_am68x_r5_defconfig
|
|
$ export UBOOT_CFG_CORTEXA=phycore_am68x_a72_defconfig
|
|
$ export TFA_BOARD=generic
|
|
$ export TFA_EXTRA_ARGS="K3_USART=0x8"
|
|
$ export OPTEE_PLATFORM=k3-j784s4
|
|
$ export OPTEE_EXTRA_ARGS="CFG_CONSOLE_UART=0x8"
|
|
|
|
1. Trusted Firmware-A:
|
|
|
|
.. include:: ../ti/k3.rst
|
|
:start-after: .. k3_rst_include_start_build_steps_tfa
|
|
:end-before: .. k3_rst_include_end_build_steps_tfa
|
|
|
|
2. OP-TEE:
|
|
|
|
.. include:: ../ti/k3.rst
|
|
:start-after: .. k3_rst_include_start_build_steps_optee
|
|
:end-before: .. k3_rst_include_end_build_steps_optee
|
|
|
|
3. U-Boot:
|
|
|
|
* 3.1 R5:
|
|
|
|
.. include:: ../ti/k3.rst
|
|
:start-after: .. k3_rst_include_start_build_steps_spl_r5
|
|
:end-before: .. k3_rst_include_end_build_steps_spl_r5
|
|
|
|
* 3.2 A72:
|
|
|
|
.. include:: ../ti/k3.rst
|
|
:start-after: .. k3_rst_include_start_build_steps_uboot
|
|
:end-before: .. k3_rst_include_end_build_steps_uboot
|
|
|
|
uSD Card creation
|
|
-----------------
|
|
|
|
Use fdisk to partition the uSD card. The layout should look similar to:
|
|
|
|
.. code-block:: bash
|
|
|
|
$ sudo fdisk -l /dev/mmcblk0
|
|
Disk /dev/mmcblk0: 15 GB, 15913189376 bytes, 31080448 sectors
|
|
242816 cylinders, 4 heads, 32 sectors/track
|
|
Units: sectors of 1 * 512 = 512 bytes
|
|
|
|
Device Boot StartCHS EndCHS StartLBA EndLBA Sectors Size Id Type
|
|
/dev/mmcblk0p1 * 128,0,1 1023,3,32 16384 278527 262144 128M c Win95 FAT32 (LBA)
|
|
/dev/mmcblk0p2 1023,3,32 1023,3,32 278528 1693883 1415356 691M 83 Linux
|
|
|
|
|
|
Once partitioned, the boot partition has to be formatted with a FAT filesystem.
|
|
Assuming the uSD card is `/dev/mmcblk0`:
|
|
|
|
.. code-block:: bash
|
|
|
|
$ mkfs.vfat /dev/mmcblk0p1
|
|
|
|
To boot from a micro SD card on a HSFS device simply copy the following
|
|
artifacts to the FAT partition:
|
|
|
|
* tiboot3.bin from R5 build
|
|
* tispl.bin from Cortex-A build
|
|
* u-boot.img from Cortex-A build
|
|
|
|
Boot
|
|
----
|
|
|
|
Put the uSD card in the slot on the board and apply power. Check the serial
|
|
console for output.
|
|
|
|
Boot Modes
|
|
----------
|
|
|
|
The phyBOARD-Izar development kit supports booting from many different
|
|
interfaces. By default, the development kit is set to boot from the micro-SD
|
|
card. To change the boot device, DIP switches S8 and S7 can be used.
|
|
Boot switches should be changed with power off.
|
|
|
|
.. list-table:: Boot Modes
|
|
:widths: 16 16 16
|
|
:header-rows: 1
|
|
|
|
* - Switch Label
|
|
- SW8: 12345678
|
|
- SW7: 12345678
|
|
|
|
* - uSD
|
|
- 00000000
|
|
- 01000001
|
|
|
|
* - eMMC (FS/UDA)
|
|
- 00000000
|
|
- 10001011
|
|
|
|
* - eMMC (HW partitions)
|
|
- 00000010
|
|
- 10001011
|
|
|
|
* - OSPI0
|
|
- 00000010
|
|
- 00001100
|
|
|
|
.. include:: k3-common.rst
|
|
|
|
Further Information
|
|
-------------------
|
|
|
|
Please see :doc:`../ti/j721s2_evm` chapter for further J721S2 SoC family
|
|
related documentation.
|