The flavor string was naively parsed using sed by removing everything
before the first hyphen, this breaks for -rc kernels. Instead lets glob
/usr/share/kernel for the installed kernel flavor. This will also
prevent the kernel being flashed if the running kernel has a different
localversion than the updated one.
[ci:skip-build] already built successfully in CI
Allow users in group "input" to control the tm2-touchkey leds.
Additionally correcting the udev rule for disabling the tm2-touchkey leds by default.
[ci:skip-build] already built successfully in CI
Add ttyescape, a script and triggerhappy configuration to allow mobile device
users to access and use a shell without having to plug in to a computer.
One of the largest limitations with a mobile device is the lack of keyboard, for
mainstream OSs like Android and iOS, this is a non-issue as the whole OS stack
is built to automatically recover in case of a crash / hang, hiding the internal
state of affairs from users and making use of careful design to minimise the
impact. When bringing Linux to mobile, we carry not only the benefits of the
Linux desktop but also it's limitations. In the event that your desktop manager
goes haywire or hangs completely, or your graphics drivers get unhappy, the
ability to quickly jump to a tty and start killing bad behaving programs or
reset your display manager is one that most of us take for granted. But when
hit by similar errors on a mobile device there is no such recourse available,
users either have to reboot and hope that the issue doesn't occur again, or pull
out a laptop and pull up a shell (assuming ssh is enabled and the rndis
interface comes up).
ttyescape proposes to solve this issues by pieceing together several already
available tools, notably:
- triggerhappy, a tool used to perform actions when
certain buttons or key combinations are pressed with no dependencies on the
display manager in use.
- fbkeyboard, a framebuffer keyboard for tty's, it
renders on top of the current tty and uses the device touchscreen as input.
This device runs on linux-postmarketos-rockchip which at the moment of
writing is 5.13.0 with (only) 6 patches applied, so close-to mainline.
I personally use 2 of these devices with postmarketOS installed daily as
my homeserver setup and it has worked really well. It's also a good
target to run Plasma Bigscreen on as a TV setupbox
gzip results in a boot.img that's too big (over 8 MB) for e.g.
samsung-i9300, so let's replace it with something that produces
smaller kernels. With this, the entire boot.img is 6,3 MB (down
from 8MiB, or 8.5458944 MB) which leaves plenty of space on the
8 MB partition and prevents the recovery from being overwritten
when this kernel is flashed.
Tested and works on samsung-i9300.
[ci:skip-build] already built successfully in CI
This provides a mobile-friendly music player in the default
installation which is something that's currently lacking.
[ci:skip-vercheck]: _pmb_recommends change doesn't need pkgrel bump
The networkmanager hotspot needs to have DHCP input enabled on the wifi
interfaces so the temporary dnsmasq instance can work. The
networkmanager backend is also switched to the nftables one so it can
create the ad-hoc hotspot forwarding/masquerade table.
Proper fix for the monospace fonts seen when postmarketos-ondev is
installed without also installing osk-sdl. This doesn't happen anymore
with pmbootstrap install --ondev, because it will always pull in osk-sdl
again for other reasons. However, since postmarketos-ondev is using this
font, let's directly depend on it instead of having it pulled in as side
effect of also having osk-sdl installed.
And extend bootloader CMDLINE per default, giving us the option to
change the CMDLINE both via the kernel config and from samsung's
S-BOOT shell.
Note: the default console in exynos_defconfig (which this config is
based on) is ttySAC1, but all midas devices uses ttySAC2, so set it to
ttySAC2 instead. Also remove all other variables. They are not needed,
and (at least) root=/dev/ram0 seem to prevent us from booting pmos.
[ci:skip-build] already built successfully in CI
uim-selection has "after *" in it's dependencies to make sure the
theoretical up to ~1min delay can't be observed. Unfortunaely this
causes incorrect dependencies ordering if one of other services depends
on ofono or modemmanager. Drop "after *" so modem can always be started
properly.
NymphCast is a FOSS Chromecast replacement (not a drop-in one though)
and allows you to "cast" audio and video to your device running the
nymphcast server. Plasma Bigscreen seems like an ideal use-case for this
so let's install and launch it by default. People can always uninstall
it anyways
Merged in mainline since 5.9-rc2-next-grate:
- all previously applied patches specific for Tegra and Nexus 7
New features, not merged yet in mainline (only in -next-grate):
- improved power management
- implemented USB OTG
New configuration options
- enable F2FS support (incl. compression), which leads to prolonging
eMMC life
Tested on E1565.
Signed-off-by: David Heidelberg <david@ixit.cz>
This allows using lm_sensors to read temperature data on the pinebook
pro (and probably other devices too)
❯ sensors
gpu_thermal-virtual-0
Adapter: Virtual device
temp1: +41.1°C (crit = +95.0°C)
tcpm_source_psy_4_0022-i2c-4-22
Adapter: rk3x-i2c
in0: 5.00 V (min = +5.00 V, max = +5.00 V)
curr1: 2.50 A (max = +2.50 A)
cw2015_battery-i2c-4-62
Adapter: rk3x-i2c
in0: 4.24 V
curr1: 0.00 A
cpu_thermal-virtual-0
Adapter: Virtual device
temp1: +47.5°C (crit = +95.0°C)
nvme-pci-0100
Adapter: PCI adapter
Composite: +31.9°C (low = -273.1°C, high = +80.8°C)
(crit = +80.8°C)
Sensor 1: +31.9°C (low = -273.1°C, high = +65261.8°C)
Sensor 2: +37.9°C (low = -273.1°C, high = +65261.8°C)
[ci:skip-build] Already built on CI
5.13.5 had some rockchip-related fixes in the changelog, so I figured
why not upgrade to it.
These patches from Manjaro seem to be the bare minimum required to get
usb-c charging and device peripherial support working again (external
display still doesn't work)
[ci:skip-build] already built successfully in CI
There's a generic udev rule to set group ownership of backlights to
'video', but it only runs on the ADD action, which seems to be too
late(?) since the backlight device is never owned by 'video' on boot.
This rule will run on CHANGE too, which might be overkill but seems to
get the job done. It's now possible to set the backlight brightness on
the PBP as a normal user.
llvm was left over from Martijn's efforts to reduce the kernel size
The drivers for external DP are enabled here, but all patches from
manjaro that deal with DP/typec alt mode, etc are dropped since they do
not solve anything on their own and may cause display instability
issues...
[ci:skip-build]: already built successfully in CI
Clayton Craft